Acrylic Interior Car LED Strip Light with Wireless APP, RGB 6 in 1…

Updated review
Updated to 5 stars!Installed the “Dreamcolor” 6 piece set on my 2023 Hyundai Palisade Limited. Here are a few things to know about this product.Installation:Fairly straight forward, electrically speaking. Main control box goes hardwired to accessory power in the fuse panel; sub-control boxes need individual 12V *constant* power (one on each door), but connect to main control box wirelessly (color control-wise). Note, these only come on when power is applied to the main control box, so no battery discharge should be expected.Placement:Location wise, my install was easier than most as my car’s trim level (Palisade Limited) has the slots for ambient lighting from factory, they just don’t come installed unless you go with the highest trim (Calligraphy). Even still, getting through the door panels themselves was a challenge. Once through, a bit of finesse sets them nicely into the factory slots. Cut to size and tape off end as stated by others. The two dash strips were easier to install (these do go hardwired into the main control box), but required quite a bit of fragile panel and hardware removal. If you’re not used to removing and replacing trim panels, this could be intimidating for some. If you do not have factory slots for ambient lighting, this kit may be a bit challenging to install due to extremely tight tolerances between panels.Final look:Overall, they look and work great. The lights can be controlled via a small button which you can hide discretely under your knee board trim panel. It is however a bit tricky to cycle through the many colors and patterns to get to the color and/or pattern you want. Note, this button does not control brightness level, only color/pattern selection. Your other option is to control your color/pattern AND brightness settings via the app which works a lot quicker for specific settings. There are a ton of color options. I have mine set to a constant, low light cyan which matches a lot of my factory interior lighting, and is mostly visible at night. This kit can be set bright enough to be seen in day light though. Also, the kit remembers your last color/pattern setting and remains there after turning the vehicle off/on.I ordered this kit to look as closely as absolutely possible to the stock ambient lighting kit that comes on the Calligraphy trim. Why not get the highest trim and get the whole thing from factory instead? Among a (very) few minor other options, I saved about $7K off MSRP going with the Limited trim level. So this kit at the price point was the best choice in my case. I’ve gotten many compliments on the install as they look and fit great.One quick note on kit selection:I unknowingly chose the “Dreamcolor” kit, and I did not know that this particular kit flashes a quick rainbow color marquee pattern at each startup, before going to your previous color/pattern selection. I did not like this small detail at all. I instead preferred to have the kit simply power up to my selected color and/or pattern ONLY. *Please not, if you want this last option like I did, you will have to choose the RBG kit instead*. If you want the rainbow marquee pattern at startup, then the Dreamcolor kit will get the job done.As for the seller:GREAT help and communication resolving my issue of the unwanted rainbow pattern. They very quickly and graciously sent me an RBG replacement kit without issue. I just tested it, and sure enough, no rainbow pattern at startup! Just simply starts to my last color choice, exactly as I wanted initially. Excellent communication and assistance from the seller.Upgraded my review to 5 stars as a result of their help. Please note I am not being paid to write this. Just honestly grateful for outstanding customer service.Highly recommend this product and seller!

Quality lights!
Full review: First off, quality lights that work great and have a ton of optional patterns/colors.Precautions: if you cut the light strip at an angle then be aware that too sharp of an angle will not allow the strip to emit light in that section. If you 90 degree/straight cut the strip then the light will emit all the way to the end. ***MAKE SURE YOU TEST ALL main and sub boxes with lights before installing. YOU HAVE TO SYNC EACH SUB BOX WITH THE MAIN BOX BEFORE FINAL INSTALLATION. I recommend laying out your entire setup on the floor/ground and make sure all is working as if the entire unit is installed. This also is important so you can see the orientation of the lights patterns. I have mine installed where the lights pan out from the center of the vehicle to the doors or from the doors to the center. You have a bunch of settings to make the lights go in or out. Again, you just want to make sure you install the strips in uniform so you don’t have them going left to right on one side and right to left on the other. For a full custom fit I removed the led door lights and storage lights from their housings. Basically leaving the led board exposed. I then removed the factory door handle and storage leds on my 2021 Yukon and placed the new LEDs over the existing factory holes and secured them in place with hot glue. This way I wasn’t drilling holes in the door panels. Make sure you are using hot glue, double sided tape, zip ties and whatever else is needed to keep wires from just laying in the doors or dash. This way you won’t hear the wires smacking around or creating a rattling noise under the dash. As you can tell in the comparison photos of my rear door the dimmest setting is still bright. The brightest setting will literally blind you. Unless you’re parked and throwing a party inside your vehicle I’m not sure when you would have these lights brighter than the dimmest setting.My only complaints are that I wish the lights were able to be more dim and I wish you could change the start up pattern.If you plan on doing the install yourself and want a full custom fit with professional look it is completely possible, but prepaid yourself for a full day project.I 100% recommend this product.